Abstract  A novel disposable amperometric biosensor strip for determination of blood alcohol concentration (BAC) with small volume of sample has been constructed using screen-printed electrodes (SPE), nanocomposite film and alcohol dehydrogenase (ADH). Firstly, the GNPs-MWCNT-Nafion nanocomposite film modified on a working electrode was made of Nafion-117, multi-wall carbon nanotubes (MWCNT) and gold nanoparticles (GNPs). After that Meldola's blue (MB) acted as an electron transfer mediator and the mixed solution of ADH, nicotinamide adenine dinucleotide (NAD(+)) were modified in order on the nanocomposite film. At last, a hydrophilic membrane which had an eyehole in center was placed at the outermost of the working area to make a reaction tank of 5 μL, then the hydrophilic membrane/ADH-NAD(+)/GNPs-MWCNT-MB-Nafion/SPE was prepared. The detection of BAC can be accomplished with 5 μL of blood sample obtained precisely by siphonage. Optimum conditions of the biosensor were experimentally determined by varying several important parameters: working potential, solution pH value, environmental temperature and interferences. Experimental results indicated that the biosensor possessed a good accuracy and stability, the linear response range was 2.0 × 10(-4) to 25 × 10(-3)mol/L and the detection limit of the biosensor was 5.0 × 10(-5)mol/L (S/N=3). In the measurement of blood samples, the proposed biosensor had excellent detection performance for measuring BAC and showed a good correlation with gas chromatography. The prepared biosensor strip can be valid for the analysis of BAC.

Abstract  A prototype amperometric immunosensor was evaluated based on the adsorption of antibodies onto perpendicularly oriented assemblies of single wall carbon nanotubes called SWNT forests. The forests were self-assembled from oxidatively shortened SWNTs onto Nafion/iron oxide coated pyrolytic graphite electrodes. The nanotube forests were characterized using atomic force microscopy and resonance Raman spectroscopy. Anti-biotin antibody strongly adsorbed to the SWNT forests. In the presence of a soluble mediator, the detection limit for horseradish peroxidase (HRP) labeled biotin was 2.5 pmol ml(-1) (2.5 nM). Unlabelled biotin was detected in a competitive approach with a detection limit of 16 nmol ml(-1) (16 microM) and a relative standard deviation of 12%. The immunosensor showed low non-specific adsorption of biotin-HRP (approx. 0.1%) when blocked with bovine serum albumin. This immunosensing approach using high surface area, patternable, conductive SWNT assemblies may eventually prove useful for nano-biosensing arrays.

Abstract  A novel amperometric sensor and chromatographic detector for determination of parathion has been fabricated from a multi-wall carbon nano-tube (MWCNT)/Nafion film-modified glassy-carbon electrode (GCE). The electrochemical response to parathion at the MWCNT/Nafion film electrode was investigated by cyclic voltammetry and linear sweep voltammetry. The redox current of parathion at the MWCNT/Nafion film electrode was significantly higher than that at the bare GCE, the MWCNT-modified GCE, and the Nafion-modified GCE. The results indicated that the MWCNT/Nafion film had an efficient electrocatalytic effect on the electrochemical response to parathion. The peak current was proportional to the concentration of parathion in the range 5.0x10(-9)-2.0x10(-5) mol L(-1). The detection limit was 1.0x10(-9) mol L(-1) (after 120 s accumulation). In high-performance liquid chromatography with electrochemical detection (HPLC-ED) a stable and sensitive current response was obtained for parathion at the MWCNT/Nafion film electrode. The linear range for parathion was over four orders of magnitude and the detection limit was 6.0x10(-9) mol L(-1). Application of the method for determination of parathion in rice was satisfactory.

Abstract  A dynamic supported liquid membrane tip extraction (SLMTE) procedure for the effective extraction and preconcentration of glyphosate (GLYP) and its metabolite aminomethylphosphonic acid (AMPA) in water has been investigated. The SLMTE procedure was performed in a semi-automated dynamic mode and demonstrated a greater performance against a static extraction. Several important extraction parameters such as donor phase pH, cationic carrier concentration, type of membrane solvent, type of acceptor stripping phase, agitation and extraction time were comprehensively optimized. A solution of Aliquat-336, a cationic carrier, in dihexyl ether was selected as the supported liquid incorporated into the membrane phase. Quantification of GLYP and AMPA was carried out using capillary electrophoresis with contactless conductivity detection. An electrolyte solution consisting of 12 mM histidine (His), 8 mM 2-(N-morpholino)ethanesulfonic acid (MES), 75 microM cetyltrimethylammonium bromide (CTAB), 3% methanol, pH 6.3, was used as running buffer. Under the optimum extraction conditions, the method showed good linearity in the range of 0.01-200 microg/L (GLYP) and 0.1-400 microg/L (AMPA), acceptable reproducibility (RSD 5-7%, n=5), low limits of detection of 0.005 microg/L for GLYP and 0.06 microg/L for AMPA, and satisfactory relative recoveries (90-94%). Due to the low cost, the SLMTE device was disposed after each run which additionally eliminated the possibility of carry-over between runs. The validated method was tested for the analysis of both analytes in spiked tap water and river water with good success.

Abstract  We report the development and application of a capillary hollow fibre membrane interface using methanol as an acceptor phase to deliver target analytes to an electrospray ionization source and a triple quadrupole mass spectrometer. Superior fluid handling systems lead to greater signal stability and membrane integrity for the continuous on-line monitoring of polar and charged analytes in complex aqueous samples with detection limits in the parts-per-trillion to parts-per-billion range. The system can be operated in either a continuous flow or a stopped acceptor flow mode - the latter giving rise to greater sensitivity. We report detection limits, enrichment factors and signal response times for selected analytes with polydimethylsiloxane and Nafion® polymer membrane interfaces. In addition, we demonstrate the use of this interface to detect pharmaceuticals and other contaminants in natural water and artificial urine. The improved sensitivity and analytical response times of our CP-MIMS system make it possible to continuously monitor dynamic chemical systems with temporal resolutions on the order of minutes. Presented is a comparison of the performance of CP-MIMS versus direct infusion electrospray ionization, demonstrating the potential advantages over direct infusion for trace analyte measurements in complex, high ionic strength samples. Furthermore, by continuously flowing a reaction mixture in a closed loop over the interface, we demonstrate the use of the system as an in situ reaction-monitoring platform for the chlorination of a model organic compound in aqueous solution.

Abstract  Large-scale energy storage has become the main bottleneck for increasing the percentage of renewable energy in our electricity grids. Redox flow batteries are considered to be among the best options for electricity storage in the megawatt range and large demonstration systems have already been installed. Although the full technological potential of these systems has not been reached yet, currently the main problem hindering more widespread commercialization is the high cost of redox flow batteries. Nafion, as the preferred membrane material, is responsible for about 11% of the overall cost of a 1 MW/8 MWh system. Therefore, in recent years two main membrane related research threads have emerged: 1) chemical and physical modification of Nafion membranes to optimize their properties with regard to vanadium redox flow battery (VRFB) application; and 2) replacement of the Nafion membranes with different, less expensive materials. This review summarizes the underlying basic scientific issues associated with membrane use in VRFBs and presents an overview of membrane-related research approaches aimed at improving the efficiency of VRFBs and making the technology cost-competitive. Promising research strategies and materials are identified and suggestions are provided on how materials issues could be overcome.

Abstract  NO and its derivative ONOO- are potent free radicals that can cause cell damage, especially in the presence of O2. To determine the potential pulmonary toxicities of nitric oxide (NO) and peroxynitrite (ONOO-) in vitro, Survanta (2.5 mg/ml) was exposed to ONOO- (0.3-8 mM) in the presence of two different buffering systems (N-2-hydroxyethylpiperazine-N'-2-ethanesulfonic acid and phosphate buffer) and minimum surface tension (MST) was determined with an oscillating bubble surfactometer. Significant increases in MST were seen only with exposure to 8 mM ONOO-, indicating that in vitro, high concentrations of ONOO- can inhibit natural surfactant function. The in vivo effects of NO and hyperoxia were then studied in four groups of newborn piglets ventilated for 48 h with 21% O2, 100% O2, 21% O2 and 100 ppm NO, or with 90% O2 and 100 ppm NO. Five animals served as an untreated control group. Bronchoalveolar lavage fluid (BAL) obtained at 48 h was subjected to centrifugation and the surfactant pellet was reconstituted to 5 mg phospholipid/ml. Significant increases in MST were seen in surfactant from piglets ventilated with NO and 90% O2, compared with either untreated controls or piglets ventilated with 21% O2 for 48 h (P < 0.05, analysis of variance). Significant increases in neutrophil chemotactic activity (NCA) of BAL were also found in the NO and O2 group (P < 0.05), with significant positive interaction between NO and O2 found (P < 0.01).(ABSTRACT TRUNCATED AT 250 WORDS)

Abstract  The electrochemical detection of As(III) was investigated on a platinum-iron(III) nanoparticles modified multiwalled carbon nanotube on glassy carbon electrode(nanoPt-Fe(III)/MWCNT/GCE) in 0 1 M H(2)SO(4) The nanoPt-Fe(III)/MWCNT/GCE was prepared via continuous potential cycling in the range from -0 8 to 0 7 V (vs Ag/AgCl), in 0 1 M KCl solution containing 0 9 mM K(2)PtCl(6) and 0 6 mM FeCl(3) The Pt nanoparticles and iron oxide were co-electro-deposited into the MWCNT-Nafion composite film on GCE The resulting electrode was examined by cyclic voltammetry (CV), scanning electron microscopy (SEM), and anodic stripping voltammetry (ASV) For the detection of As(III), the nanoPt-Fe(III)/MWCNT/GCE showed low detection limit of 10 nM (0 75 ppb) and high sensitivity of 4 76 mu A mu M(-1), while the World Health Organization's guideline value of arsenic for drinking water is 10 ppb It is worth to note that the electrode presents no interference from copper ion, which is the most serious interfering species in arsenic detection

Abstract  In a study screening anaerobic microbes utilizing D: -galactitol as a fermentable carbon source, four bacterial strains were isolated from an enrichment culture producing H₂, ethanol, butanol, acetic acid, butyric acid, and hexanoic acid. Among these isolates, strain BS-1 produced hexanoic acid as a major metabolic product of anaerobic fermentation with D: -galactitol. Strain BS-1 belonged to the genus Clostridium based on phylogenetic analysis using 16S rRNA gene sequences, and the most closely related strain was Clostridium sporosphaeroides DSM 1294(T), with 94.4% 16S rRNA gene similarity. In batch cultures, Clostridium sp. BS-1 produced 550 ± 31 mL L⁻¹ of H₂, 0.36 ± 0.01 g L⁻¹ of acetic acid, 0.44 ± 0.01 g L⁻¹ of butyric acid, and 0.98 ± 0.03 g L⁻¹ of hexanoic acid in a 4-day cultivation. The production of hexanoic acid increased to 1.22 and 1.73 g L⁻¹ with the addition of 1.5 g L⁻¹ of sodium acetate and 100 mM 2-(N-morpholino)ethanesulfonic acid (MES), respectively. Especially when 1.5 g L⁻¹ of sodium acetate and 100 mM MES were added simultaneously, the production of hexanoic acid increased up to 2.99 g L⁻¹. Without adding sodium acetate, 2.75 g L⁻¹ of hexanoic acid production from D-galactitol was achieved using a coculture of Clostridium sp. BS-1 and one of the isolates, Clostridium sp. BS-7, in the presence of 100 mM MES. In addition, volatile fatty acid (VFA) production by Clostridium sp. BS-1 from D-galactitol and D: -glucose was enhanced when a more reduced culture redox potential (CRP) was applied via addition of Na₂S·9H₂O.

Abstract  One acetamide and 5 acetanilide herbicides are currently registered for use in the United States. Over the past several years, ethanesulfonic acid (ESA) and oxanilic acid (OA) degradation products of these acetanilide/acetamide herbicides have been found in U.S. ground waters and surface waters. Alachlor ESA and other acetanilide degradation products are listed on the U.S. Environmental Protection Agency's (EPA) 1998 Drinking Water Contaminant Candidate List. Consequently, EPA is interested in obtaining national occurrence data for these contaminants in drinking water. EPA currently does not have a method for determining these acetanilide degradation products in drinking water; therefore, a research method is being developed using liquid chromatography/negative ion electrospray/mass spectrometry with solid-phase extraction (SPE). A novel chromatographic separation of the acetochlor/alachlor ESA and OA structural isomers was developed which uses an ammonium acetate-methanol gradient combined with heating the analytical column to 70 degrees C. Twelve acetanilide degradates were extracted by SPE from 100 mL water samples using carbon cartridges with mean recoveries >90% and relative standard deviations < or =16%.

Abstract  A novel highly sensitive biosensor for the direct and simultaneous determination of superoxide anion radical (O2-) and nitrite (NO2-) was developed by incorporation of carbon nanotube (CNT) solubilized in nafion in polypyrrole (PPy) matrix on Pt electrode followed by immobilization of Cu,ZnSOD (SOD1) on it. The CNT/PPy nanocomposite electrode enhanced the immobilization of SOD1 and promoted the electron transfer of SOD1 minimizing its fouling effect. The surface morphological images of PPy and CNT-PPy nanocomposite on Pt electrode were obtained by scanning electron microscopy exhibiting highly microporous structures. The electrochemical behavior of the biosensor investigated by cyclic voltammetry revealed that the SOD1 immobilized electrode showed characteristic of SOD1 quasi-reversible redox peaks with a formal potential of +0.065 V vs. Ag/AgCl. The biosensor exhibited a linear response over the concentration range from 0.1 to 750 μM, with a detection limit of 0.1±0.03 μM for O2- and a corresponding linear range of 0.5-2000 μM, with a detection limit of 0.5±0.025 μM for NO2-. In addition, the biosensor exhibited high sensitivity, good reproducibility and retained stability over 30 days. This modified electrode was quite effective not only in detecting O2- and NO2- independently but also determining the concentration of O2- and NO2- simultaneously in vitro and from cancer cells.

Abstract  A novel flow injection analysis (FIA) system suitable for measurement of S-nitrosothiols (RSNOs) in blood plasma is described. In the proposed (FIA) system, samples and standards containing RSNO species are injected into a buffer carrier stream that is mixed with the reagent stream containing 3,3'-dipropionicdiselenide (SeDPA) and glutathione (GSH). SeDPA has been shown previously to catalytically decompose RSNOs in the presence of a reducing agent, such as GSH, to produce nitric oxide (NO). The liberated NO is then detected downstream by an amperometric NO sensor. This sensor is prepared using an electropolymerized m-phenylenediamine (m-PD)/resorcinol and Nafion composite films at the surface of a platinum electrode. Using optimized flow rates and reagent concentrations, detection of various RSNOs at levels in the range of 0.25-20 μM is possible. For plasma samples, detection of background sensor interference levels within the samples must first be carried out using an identical FIA arrangement, but without the added SeDPA and GSH reagents. Subtraction of this background sensor current response allows good analytical recovery of RSNOs spiked into animal plasma samples, with recoveries in the range of 90.4-101.0%.